Digital View 559000105?3 Spezifikationen PDF herunterladen (Seite 7)

Specifications subject to change without notice

7 of 70

CONNECTION & OPERATION

CAUTION: Never connect or disconnect parts of the display system when the system is powered up as this may cause serious

damage.

CONNECTION

Connection and usage is quite straight forward (it is useful to have the relevant connection diagram available at this time):

1. LCD panel & Inverter: Connect the inverter (if it is not built-in the panel) to the CCFT lead connector of the LCD panel.

2. LVDS type panels: The controller board has the built-in LVDS transmitter driver. Plug the LVDS cable to J3. Insert the

panel end of the cable the LCD panel connector.

3. Inverter & Controller: Plug the inverter cable to CNB1 and CNA1 (if necessary). Plug another end to the connector on

the inverter.

4. Function switch & Controller: Plug the OSD switch mount cable to CNC1 on the controller board and another to the

OSD switch mount.

5. LED & Controller: Plug in a 3-way with dual colour LED to connector LED1 on the controller board.

6. IR & Controller: Plug in a 3-way with IR sensor to connector IR1 on the controller board.

7. Jumpers & Switches: Check all jumpers and switches (SW3, SW4) are set correctly. Details referring the connection

diagram (a separate document) or the jumpers and switches setting table (in the following section).

8. Jumpers & Inverter & Panel voltage: Particularly pay attention to the settings of JA3, JA5, JA6, JB2 and JB3. JB2 & JB3

are used for inverter control (read inverter specification and information on the jumper table to define the correct settings).

JA3 & JA5 & JA6 is used for panel voltage input (read panel specification and information on the jumper table to define the

correct settings).

9. VGA cable & Controller: Plug the VGA cable to the connector P1 on the controller board.

10. Power supply & Controller: Plug the DC 12V/24V power in to the connector PP5 or PP2/3. You can consider to use

DigitalView mating power cable P/N 426013800-3, 160mm for PP5 connection.

11. External panel power input : Plug power cable : P/N 426013700-3 for external panel power input (3.3 (max 7A) / 5V

(max 7A) / 12V (max 5A) / 18V (max3.5))

12. Power on: Switch on the controller board and panel by using the OSD switch mount.

13. Audio Board : The Audio Add-on Board P/N 416940020-3 is only operate under 12VDC power input environment.

14. HDMI audio output : The HDMI audio output can be connected to Audio add-on board P/N 416940020-3 by using the

audio cable P/N 426451800-3 connected between SVX-1920 (connector : CN10) and Audio add-on board P/N

416940020-3 (connector : CN2).

15. Auxiliary Digital Input Port – HD1 / HD2 : Allow the user to configure the input port configuration for supporting Digital

video signal input (e.g HDMI, DVI, HD-SDI (from HD-1000/-2000/-3000/-3000S)). Please refer to Appendix IX to configure

this auxiliary digital input port – HD1 & HD2.

General:

• If you are using supplied cables & accessories, ensure they are correct for the model of panel and controller.

• If you are making your own cables & connectors refer carefully to both the panel & inverter specifications and the section

in this manual, “Connectors, Pinouts & Jumpers” to ensure the correct pin to pin wiring.

PC SETTINGS

The controller has been designed to take a very wide range of input signals however to optimize the PC’s graphics performance

we recommend choosing 60Hz vertical refresh rate – this will not cause screen flicker.

OPERATION

Once the system has been connected and switched on there are a number of functions available to adjust the display

image as summarized in the following sections. The settings chosen will be saved for each mode independently.

1 2 3 4 5 6 7 8 9 10 11 12 ... 69 70

Kommentare zu diesen Handbüchern

Keine Kommentare

Digital View 559000105?3 Spezifikationen Seite 7

Kommentare zu diesen Handbüchern